Get quotes
TL-06, free tool

Conveyor Belt Specification Decoder

Type the marking from a belt, a quote or a datasheet. The decoder explains each part and estimates the belt's thickness, mass, working tension and smallest drive pulley.

Decode a belt marking

Width, carcass and strength, plies, covers and grade, in any common order.

Examples:
Carcass–
Strength
– N/mm
Plies, strength per ply
–
Full-width breaking strength
– kN
Working tension (rated)
– kN
Covers, top + bottom
– mm
Cover grade
–
Thickness, estimated
– mm
Mass, estimated
– kg/m²
Smallest drive pulley, guide
– mm

Conveyor belts are specified with a compact code such as 1200 EP630/4 6+2 M. Reading it correctly is the difference between a like-for-like replacement and a belt that is too weak, too stiff to trough, or wears out in months. The decoder explains each part and adds the figures suppliers and designers work from.

Reading a belt specification

  • 1200: width in mm.
  • EP: carcass fabric. E is polyester (warp, along the belt) and P is polyamide or nylon (weft, across it). NN is nylon both ways, EE polyester both ways, ST steel cord, CC or B cotton.
  • 630: the belt's minimum breaking strength in N per mm of width. A 1 200 mm EP630 belt breaks at about 756 kN.
  • /4: number of fabric plies, so each ply is an EP160. Steel-cord belts have no ply count.
  • 6+2: top (carrying) cover and bottom (pulley side) cover thickness in mm.
  • M: cover grade, the rubber's abrasion and tensile performance.

Cover grades and special properties

GradeStandardUseMax. abrasion lossMin. tensile
MSANS 1173Abrasive, heavy mining dutysee SANS 1173
NSANS 1173General dutysee SANS 1173
WDIN 22102Extreme abrasion, fine sharp ore90 mm³18 MPa
XDIN 22102Heavy impact, cutting and gouging120 mm³25 MPa
YDIN 22102Normal duty150 mm³20 MPa
ZDIN 22102Light duty250 mm³15 MPa
HISO 10247Severe cutting and gouging120 mm³24 MPa
DISO 10247High abrasion100 mm³18 MPa
LISO 10247Normal duty200 mm³15 MPa

Abrasion loss is tested to ISO 4649 (DIN 53516): lower is better. Special compounds carry extra letters: fire resistant (FR, K, S; underground coal belts must meet SANS 971), heat resistant (T1 to about 100 °C, T2 125 °C, T3 150 °C under ISO 4195), and oil resistant (OR, MOR, G). Read more on our belt types and sizes and rubber belts pages.

How the estimates are made

  • Working tension: breaking strength divided by a safety factor of 10 for fabric belts and 6.7 for steel cord, the usual starting points in DIN 22101 design.
  • Thickness and mass: covers at about 1.15 kg/m² per mm plus a carcass estimate from typical ply or cord thicknesses. Manufacturers' figures differ by a few per cent, so use the datasheet when you have it.
  • Smallest drive pulley: about 108 × carcass thickness for EP and NN, 145 × cord diameter for steel cord, rounded up to a standard size. Tail and bend pulleys can be one or two sizes smaller. This is a guide only: each manufacturer publishes its own minimum pulley table.

Frequently asked questions

What does EP630/4 mean?
A polyester-nylon (EP) fabric carcass with a breaking strength of 630 N per mm of width, made from four plies of 160 N/mm each. The marking says nothing about the covers, so a full specification adds them, for example EP630/4 6+2 M.
Is EP630/4 the same as EP630/3?
Both have the same strength, but the three-ply belt uses heavier plies. It is thinner and lighter, troughs differently and needs a different splice. Fewer plies usually means less resistance to impact and rip. Replace like with like unless your supplier has checked the change.
What is the difference between SANS 1173 and DIN grades?
They are different standards with their own test limits. SANS 1173 is the South African standard for textile-reinforced belting with grades such as M and N; DIN 22102 uses W, X, Y and Z; ISO 10247 uses H, D and L. Many suppliers quote more than one.
When do I need a steel-cord belt?
When the required rating goes beyond what a fabric belt can carry at a practical ply count, usually above about 1 600 to 2 000 N/mm, or on long conveyors where fabric belt stretch would need too much take-up travel.

Get quotes for what you have sized

Used the figures above to size a belt, drive or conveyor? Press Ask for quotes with these figures in the calculator and they are copied into the quote form at the bottom of this page. A supplier or contractor who works in your area replies directly.

More calculators and guides

Get free quotes