Get quotes
TL-07, free tool

Bulk Material Reference for Conveyors

Typical bulk densities, surcharge angles, safe inclines and belt speeds for the materials South African conveyors carry, with rules of thumb for belt width, idler spacing and standard widths.

Bulk materials

Click a material's capacity link to open the calculator with its values filled in.

MaterialBulk density t/m³SurchargeMax. inclineMax. speed m/s
Coal, run-of-mineLumpy, some fines; dusty when dry0.80–0.9020°18°4.5Capacity
Coal, washed and sizedWet off the plant; degrades at high speed0.75–0.8515°16°4Capacity
Iron ore, lumpVery abrasive, heavy impact at loading2.00–2.4015°18°4Capacity
Iron ore, finesAbrasive; sticky when wet2.20–2.6020°20°4Capacity
Manganese oreAbrasive, sharp-edged1.90–2.2020°18°3.5Capacity
Chrome oreDense, abrasive2.00–2.4020°18°3.5Capacity
Platinum ore (UG2, Merensky), crushedAbrasive; chromite-rich UG2 is heavier1.80–2.1020°18°3.5Capacity
Gold ore, crushedQuartzitic, very abrasive1.60–1.8020°18°3.5Capacity
Copper ore, crushedAbrasive1.60–2.0020°18°3.5Capacity
Crushed stone, aggregateSharp edges cut covers1.40–1.6020°16°3Capacity
Sand, dryFree flowing, rolls back on steep belts1.40–1.6015°15°3Capacity
Sand, dampCarries back on the return belt1.60–1.9020°20°3Capacity
Gravel, roundedRounded stones roll back1.50–1.8015°15°3Capacity
Limestone, crushedDusty1.40–1.6020°18°3Capacity
Cement clinkerHot and abrasive; heat-resistant belt1.20–1.5020°18°2.5Capacity
Cement, portlandFluidises when aerated; enclose the belt1.20–1.5010°20°1.5Capacity
Fly ash, dryVery dusty, flows like a liquid0.60–0.9010°15°1.5Capacity
Gypsum, crushed1.20–1.4020°18°3Capacity
Salt, coarseCorrosive to idlers and structure1.10–1.3015°18°3Capacity
CokeAbrasive and friable0.40–0.5520°18°3Capacity
Maize or wheatFree flowing; dust explosion risk0.70–0.8010°12°4Capacity
Sugar, rawSticky in humid air; food-grade belt0.88–1.0015°17°2.5Capacity
Fertiliser, granularCorrosive and oily; check cover compound0.90–1.2015°12°2.5Capacity
Wood chipsLight; capacity limited by volume0.25–0.4020°25°4Capacity
Soil and overburden, moistSticky; needs good belt cleaning1.60–2.0020°20°3.5Capacity

Typical values from CEMA and belt-manufacturer tables. Moisture, grading and lump size change all of them; for design, test your material.

Every conveyor calculation needs a few properties of the material carried: how heavy it is in bulk, how steep a heap it forms on a moving belt, how steep a conveyor it can climb without rolling back and how fast it can travel before spillage and dust get out of hand. The table above gives typical figures for the materials South African conveyors carry.

What the columns mean

  • Bulk density: mass of loose material per m³ including the voids, not the density of solid rock. Iron ore at 2.2 t/m³ is more than twice as heavy as coal per m³, so the same belt carries more than twice the tonnes.
  • Surcharge angle: the dynamic angle the top of the load makes on a moving belt, typically 5° to 15° less than the angle of repose.
  • Maximum incline: the steepest smooth-belt conveyor before material slides or rolls back. Steeper runs need chevron, cleated or sidewall belts.
  • Maximum speed: a practical upper limit for spillage, dust, wear and material damage, not a hard rule.

Rules of thumb for conveyor sizing

  • Belt width and lump size: at least 3 × the largest lump when lumps are mixed with fines (about 10 % lumps), 5 × when most of the load is lumps.
  • Idler spacing: carry idlers about 1.0 to 1.5 m apart (closer for heavy ore, wider for light loads), return idlers about 3 m, impact idlers 0.3 to 0.45 m under the loading point.
  • Belt sag: keep sag between carry idlers to about 1 to 2 % of the spacing, set by the take-up tension.
  • Loading: load centrally, in the direction of travel and as close to belt speed as possible. Most belt damage starts at a poor transfer chute.

Standard belt widths

Widths used in South Africa follow SANS 1173 and ISO 251: 300, 400, 450, 500, 600, 650, 750, 800, 900, 1000, 1050, 1200, 1350, 1400, 1500, 1600, 1650, 1800, 2000, 2100, 2200, 2400 mm. The most common on mines and plants are 600, 750, 900, 1 050, 1 200, 1 350, 1 500 and 1 800 mm. Imported equipment may use inch widths (24, 30, 36, 42, 48, 54, 60, 72 in), which are close to but not the same as the metric sizes: convert with the unit converter.

Frequently asked questions

What is the bulk density of coal?
Run-of-mine bituminous coal is about 0.80 to 0.90 t/m³ in bulk; washed and sized coal about 0.75 to 0.85 t/m³. Wet coal is heavier, and very fine coal can be lighter.
What is the maximum angle for a conveyor belt?
For a smooth belt, typically 15° to 20° for most bulk materials, as low as 12° for grain and free-flowing granules and up to 25° for wood chips. Chevron belts allow about 25° to 35° and sidewall belts up to vertical.
Why is my material rolling back on the incline?
The incline is too steep for the material, the belt is too wet or worn smooth, or the load is too thin. Round stones, dry sand and pellets are worst. A chevron belt, a lower angle or a deeper trough usually helps.

Get quotes for what you have sized

Used the figures above to size a belt, drive or conveyor? Press Ask for quotes with these figures in the calculator and they are copied into the quote form at the bottom of this page. A supplier or contractor who works in your area replies directly.

More calculators and guides

Get free quotes