Get quotes
TL-01, free tool

Conveyor Belt Capacity Calculator

Enter the belt width, speed, idler trough angle and the material you carry. The calculator gives the load cross-section and the capacity in t/h and m³/h, using the ISO 5048 method.

Capacity

Results update as you type. All calculation happens in your browser.

Not sure? Use the belt speed calculator.
Sets typical density and surcharge angle.
Slope of the load's top while moving, usually 10° to 25°.
Many designers size at 75–85 % to allow for surges.
For the belt width check.
Capacity–t/h
Volume
– m³/h
Load cross-section
– m²
Loaded width b
– mm
Centre roll length
– mm
Incline factor k
–
At 100 % fill
– t/h

Capacity is the first number in any conveyor design and the first thing a supplier asks when you request a new belt or system. It depends on how much material sits on each metre of belt (the load cross-section) and how fast the belt runs. The calculator above uses the method in ISO 5048 and DIN 22101, which most South African designers and belt suppliers work to.

How conveyor capacity is calculated

The volume flow is Qv = 3 600 × A × v × k in m³/h, where A is the load cross-section in m², v the belt speed in m/s and k a reduction factor for incline. Multiply by the bulk density in t/m³ to get t/h.

  • Loaded width b: the load never reaches the belt edge. For belts up to 2 000 mm, b = 0.9 B − 0.05 m; for wider belts, b = B − 0.25 m.
  • Cross-section A is the trough part (between the wing rolls) plus the surcharge part (the heap on top). The trough part grows with the trough angle and the centre roll length; the surcharge part grows with the material's surcharge angle.
  • Incline factor k: on a slope the heap flattens. k = 1 − (Asurcharge / A)(1 − k1), with k1 from the incline and surcharge angles.

Centre roll lengths follow ISO 1537 idler sets. SANS 1313 rolls are similar; if your idlers have a much longer or shorter centre roll the trough area changes a little.

Worked example

A 1 200 mm belt on 35° three-roll idlers, running at 2.5 m/s and carrying crushed aggregate (1.5 t/m³, 20° surcharge) on the level:

  • Loaded width b = 0.9 × 1.2 − 0.05 = 1.03 m, centre roll about 465 mm
  • Cross-section A ≈ 0.165 m²
  • Volume = 3 600 × 0.165 × 2.5 ≈ 1 485 m³/h
  • Capacity ≈ 1 485 × 1.5 ≈ 2 230 t/h at full section, or about 1 780 t/h at an 80 % design fill

Choosing speed, width and trough angle

  • Speed: higher speed gives more tonnage on a narrower, cheaper belt, but increases wear at the loading point, dust, noise and degradation of friable material. Coal and ore belts commonly run at 2.5 to 4.5 m/s, aggregate at 2 to 3 m/s, cement and fly ash at 1 to 1.5 m/s.
  • Width: set by both tonnage and lump size. Allow at least three times the largest lump for a well-graded feed, five times when the feed is mostly lumps.
  • Trough angle: 35° is the usual choice for bulk mining belts. 45° carries more but needs a belt with good troughability; 20° suits thick or steel-cord belts that will not trough deeply.
  • Fill: designing at full section leaves no margin for surges from a crusher or reclaimer. A 75–85 % design fill is common.

Frequently asked questions

What capacity does a 600 mm conveyor belt carry?
On 35° troughed idlers at 1.5 m/s and full section, a 600 mm belt carries about 200 m³/h, which is roughly 300 t/h of crushed stone or 170 t/h of coal. Enter your own speed and material above for a closer figure.
Which surcharge angle should I use?
Use the dynamic surcharge angle, the slope of the load while it moves, not the static angle of repose. It is usually 5° to 15° less than the angle of repose: about 20° for run-of-mine coal and crushed ore, 15° for free-flowing sand and grain, and 10° or less for cement and fly ash.
Is this the same as the CEMA method?
The principle is the same, but CEMA uses a different edge distance and its own idler dimensions, so CEMA tables give slightly lower areas for the same belt. Either is fine for a first estimate; your supplier or designer will confirm with their own figures.
Why does my conveyor carry less than the calculation?
Feed rate, not the belt, often limits tonnage: a crusher, chute or feeder that cannot deliver the full rate, or an off-centre load that has to be kept low to stop spillage. Belt slip and worn idlers also reduce the effective speed.

Get quotes for what you have sized

Used the figures above to size a belt, drive or conveyor? Press Ask for quotes with these figures in the calculator and they are copied into the quote form at the bottom of this page. A supplier or contractor who works in your area replies directly.

More calculators and guides

Get free quotes