Get quotes
TL-02, free tool

Conveyor Belt Speed Calculator

Find the belt speed of an existing conveyor from its motor, gearbox and drive pulley, or the gearbox ratio you need to reach a target speed.

Belt speed

Change any value and the results update immediately.

Nameplate speed at 50 Hz: 2-pole about 2 960, 4-pole 1 480, 6-pole 985, 8-pole 740.
50 Hz on Eskom supply; change if a variable speed drive runs the motor.
Include belt-and-pulley or chain reductions, multiplied together.
Rubber lagging is usually 10–15 mm, ceramic 12–16 mm. 0 for a bare pulley.
Gives the gearbox ratio that would reach it.
Belt speed–m/s
Belt speed
– ft/min
Belt speed
– m/min
Drive pulley speed
– rpm
Effective diameter
– mm
Time per pulley turn
– s
Ratio for target speed
– : 1

Belt speed sets a conveyor's capacity and drive power, and suppliers need it to quote a new belt, drive, pulley or idler set. On an existing conveyor you can work it out from the drive train: the motor speed, the gearbox ratio and the diameter of the drive pulley including its lagging.

The belt speed formula

v = π × D × n ÷ 60, where v is belt speed in m/s, D the effective drive pulley diameter in metres and n the drive pulley speed in rpm.

  • Pulley speed n = motor speed ÷ total reduction ratio. With a variable speed drive, motor speed scales with frequency: a 1 480 rpm motor at 40 Hz turns at about 1 184 rpm.
  • Effective diameter D = shell diameter + 2 × lagging thickness. A worn 12 mm lagging on a 630 mm pulley makes almost 4 % difference to belt speed.
  • Strictly, the belt's neutral axis sits inside the carcass, so a thick belt runs slightly faster than this figure. The difference is small (under 1 % on most belts).

Checking speed on site

The motor nameplate gives full-load speed, not synchronous speed, and a lightly loaded motor turns slightly faster. To measure the real speed, mark the belt and time one full revolution, then divide the belt length by the time. A hand-held tachometer with a contact wheel on the return belt is quicker. Only do either with the conveyor's guards in place and under your site's safety rules: never reach into a running conveyor.

Typical belt speeds

  • Light packaging and assembly lines: 0.1 to 0.5 m/s
  • Feeder belts under hoppers and bins: 0.3 to 1 m/s
  • Cement, fly ash and other fine, dusty material: 1 to 1.5 m/s
  • Aggregate, sand and quarry belts: 2 to 3 m/s
  • Coal and ore plant belts: 2.5 to 4.5 m/s
  • Long overland and in-pit steel-cord conveyors: 4 to 6 m/s

See the bulk material reference for speed limits by material.

Frequently asked questions

How do I convert ft/min to m/s?
Divide by 196.85. 500 ft/min is about 2.54 m/s. The unit converter does this and other conversions.
Can I speed up a conveyor with a VSD?
A variable speed drive can run a motor above 50 Hz, but power and belt tension rise with tonnage and the motor, gearbox, belt and pulleys all need to be checked first. Running above about 55 Hz usually needs the motor supplier's approval.
Why is my belt speed different from the design figure?
Worn or missing lagging, a replaced pulley with a different diameter, a different gearbox ratio after a repair, or belt slip on the drive pulley. Slip shows up as glazed lagging and a belt that slows under load.

Get quotes for what you have sized

Used the figures above to size a belt, drive or conveyor? Press Ask for quotes with these figures in the calculator and they are copied into the quote form at the bottom of this page. A supplier or contractor who works in your area replies directly.

More calculators and guides

Get free quotes